Skip to content

Deck Staining and Sealing


Wash, repair, sand and stain for redwood, cedar and pressure-treated decks, done by a Riverside builder who knows what the wood under the color is doing.

Deck Staining

What a Deck Staining Job Really Involves


Deck staining looks like a paint job, and that is where most of them go wrong. Stain works only when it soaks into clean, dry, open wood. Roll it over a gray, dirty deck and it sits on the surface, looks fine for a season, then wears off in blotches you cannot touch up without stripping the whole deck.

Most of a staining job happens before the can opens. We wash the deck, brighten the wood, let it dry, sand the rough spots and fix anything loose or soft. Then the stain goes on in thin coats, worked into the grain, with the excess wiped back so nothing puddles on the boards and turns sticky.

Ben has built and refinished wood decks around Riverside for 35 years, and he will tell you plainly when a deck is a stain job and when it needs more than stain. Redwood, cedar and pressure-treated lumber each take finish differently. The product we pick depends on the wood and on how hard the sun hits that side of the house.

Freshly stained wood deck with a glossy finish, a wood railing and a dining set, trees beyond

Clear, Toned, Semi-Transparent or Solid


Stain is sold by how much pigment it carries. More pigment blocks more sun and shows less grain. This is how Ben walks homeowners through the four choices at the kitchen table.

Clear Sealer

A water repellent with little or no pigment. The wood keeps its natural look and sheds water, but there is almost nothing in it to stop the sun, so in Inland Empire light the boards still go gray and the coat needs redoing often.

Transparent Toner

A light tint over the grain. It evens out color between new and old boards and slows graying a little. Good on new redwood or cedar when you want the wood to look like wood. On a sunny deck, plan on a short recoat cycle.

Semi-Transparent

Enough pigment to give real sun protection while the grain still reads through. This is the stain we recommend most for decks, because it wears by fading instead of peeling, and the next coat goes on after a wash rather than a strip.

Solid Color

Hides the grain completely and blocks the most UV. It behaves more like paint, which is great on railings and fascia but can peel on a walking surface where feet and chair legs scuff it. We use it on decks with patched or mismatched boards.

How Each Wood Takes Stain


Stained cedar side gate with a Z-brace

Redwood and cedar are soft, open-grained woods with natural oils, and they take a penetrating stain readily. They also show every lap mark if stain gets brushed on unevenly in hot sun, so we work a few boards at a time, end to end, in the cooler part of the day.

Pressure-treated lumber is a different animal. New boards often arrive wet from the treatment and will not absorb stain until they dry out, which can take weeks or longer depending on the weather. The test is simple: sprinkle water on a board. If it beads, wait. If it soaks in, the wood is ready.

The same rules apply to the rest of the wood around a deck. A cedar gate like this one takes the same wash and the same stain so it matches the boards next to it. If you are replacing a fence as well, we can stain it on the same visit so the whole yard reads as one color.

Our Sequence

Inspect, Wash, Brighten, Sand, Stain


A staining job runs over a few days, mostly because wet wood has to dry between steps. Here is the order and why each step is there.

01

Inspect and Repair

Ben walks every board, probes the posts and the ledger, sets popped nails and swaps loose or split boards. Soft wood gets cut out before it gets colored. If the frame needs more than a few boards, it becomes a deck repair first.

02

Wash and Brighten

A deck cleaner lifts dirt, mildew and the gray, sun-burned surface. We keep the pressure low, because a narrow tip at full blast furs the grain and gouges soft redwood. A brightener follows to neutralize the cleaner and bring the wood’s color back.

03

Sand and Stain

Once the wood is dry, we sand down raised fibers and splinters, then apply stain in thin coats, back-brushing it into the grain and wiping off what the wood will not take. Nobody walks on it until the cure time on the label has passed.

Get a Staining Quote From Ben

(909) 227-4193

Call to set up a look at your deck. Ben will check the wood, tell you which stain he would use and why, and put the price on paper.

Schedule a Look

How Fast Inland Empire Sun Wears Down a Finish


Out here the sun does most of the damage. UV breaks down the wood fibers at the surface along with the pigment in the stain, and the flat boards of a deck take it far harder than the railings or the siding. A deck facing south or west in Riverside, Fontana or Moreno Valley fades faster than a shaded one on the same street.

No fixed schedule fits every deck, so Ben gives you a test instead. Every spring, splash water on the boards that get the most sun. If it beads up, the finish is still working. If it soaks in and darkens the wood, it is time for a wash and a fresh coat. Walking paths and stair treads usually go first.

Shade buys you years. A deck under a stained wood patio cover like this one holds its finish far longer than one in open sun. If the wash turns up gray, soft wood near the house or at the board ends, that is dry rot, a fungus that needs moisture, and it gets cut out and replaced before any stain goes on.

Brown stained wood patio cover attached to a stucco house

Other Wood We Finish and Build


A house with a deck usually has other exterior wood asking for the same care. Everything we do is listed on our services page.

Exterior Painting

Siding, trim, fascia and doors prepped and painted with coatings chosen for Inland Empire heat.

See Exterior Painting

Wood Patio Covers

Attached and freestanding wood covers, permitted and built to shade a deck or patio through decades of sun.

See Patio Covers

Deck Repair

Loose boards, rotted joists, failing posts and ledgers fixed to code, so the deck is worth staining again.

See Deck Repair
Common Questions

Deck Staining Questions, Code and Otherwise


Do I need a permit to stain or seal my deck?

No. In most Inland Empire cities, cleaning, sanding and staining an existing deck is finish work and does not need a building permit. That changes if the job turns into structural repair, such as replacing joists, beams, posts or the ledger, which usually does need one. Swapping a few deck boards like for like is often exempt, but your city’s building department decides. If we find structural damage during prep, Ben will stop, show you, and handle the permit before any framing work starts.

Will staining my deck bring it up to code?

No. Stain is a finish. The code items on an older deck are the guard height, the openings in the railing, the stairs and the way the ledger is attached to the house. On a single-family home, a deck more than 30 inches above grade needs a guard at least 36 inches tall, with openings that will not pass a 4-inch sphere. If your railing falls short while we are prepping, we will point it out and you can decide what to do about it.

Can a composite deck be stained?

Generally no, and it should not need it. Capped composite boards carry their color in the outer shell, and stain has no open grain to soak into, so it sits on top and wears off in patches. If you have an older, uncapped composite deck, check what its maker allows before putting anything on it. What a composite deck often does need is attention to the wood around it: a redwood rail cap, the wood stair stringers, the fascia and the patio cover overhead. We stain those on the same visit so they match.

Are there California rules on which stains can be used?

Yes. California air quality rules limit the solvent content, called VOCs, in architectural coatings, and the South Coast air district that covers much of Riverside and San Bernardino counties holds some of the strictest limits in the country. Some stain formulas sold in other states are not sold here for that reason. We use compliant products, and they hold up well when the prep is right.

Can rotted boards be stained over and fixed later?

You can, but you should not. Stain over decayed wood hides the problem while the fungus keeps working, and dry rot needs moisture to spread, which a deck in a sprinkler zone has plenty of. A soft board at the edge can mean a soft joist under it. We probe the frame before we stain, replace boards like for like where that is all it takes, and tell you when a repair is big enough that it needs a permit.

How long should a new pressure-treated deck dry before staining?

Until it passes the water test. Fresh pressure-treated lumber is often still wet from treatment, and stain will not soak in until it dries, which can take weeks or longer depending on the weather and the season. Splash some water on a board: if it beads, wait; if it soaks in, the wood is ready. Redwood and cedar can usually be stained much sooner, once they are clean and dry.

Ready to Get Ahead of the Sun?


35 years of building and refinishing wood in Riverside and San Bernardino counties. A clean deck, the right stain and an honest price.

(909) 227-4193 ben.bpp@gmail.com Ask Ben for a Staining Quote

Where We Work


Based in Riverside, CA, serving homeowners across Riverside and San Bernardino counties.