Skip to content

Window Installation

Replacement windows and new-construction windows installed in Riverside, CA. Vinyl, fiberglass, and aluminum frames, dual-pane Low-E glass, full permit service, and a weathertight seal that passes inspection the first time.

Window Installation

We Measure. We Remove. We Install.

Bad windows leak air, fog up between the panes, stick in their tracks, and drive your summer electric bill straight up. BPP Construction replaces them. We measure every opening to the sixteenth of an inch, pull the old units, prep the frame, set the new windows plumb and square, and seal them against water and air. With 35 years building in the Inland Empire, Ben knows exactly how Riverside heat and clay-soil house movement work on a window opening, and he installs for it.

There are two jobs people call window installation, and they are not the same. A replacement window drops into your existing frame when the frame is still sound, so the wall stays closed and the job moves fast. A new-construction window is fastened with a nailing flange to the wall framing itself, which means opening the wall, integrating flashing with the weather barrier, and re-finishing the interior and exterior. BPP Construction does both. We tell you which one your house actually needs before we quote it, not after.

Every window we set gets proper flashing, backer rod, and sealant at the perimeter so water has nowhere to get behind the frame. We re-insulate the gap between window and rough opening, not just foam the visible edge. And when the city wants an egress window in a bedroom or a tempered pane next to a door, we know the code section and we build to it. Ben pulls the permit, schedules the inspection, and stands there while the inspector signs off.

New dual-pane window installed by BPP Construction in Riverside, CA
Built to Standard

Windows Installed Right

35
Years Experience
in the Inland Empire
100%
Fully Permitted
Work
2hrs
Average Single-Window
Install Time
25+
Cities Served
Two Counties
Our Process

From Measurement to Final Seal

01

Measurement & Selection

We measure every opening for width, height, and squareness, then check the existing frame for rot, racking, and water damage. That tells us whether you need replacement windows or new-construction windows. We help you pick frame material, glass package, and operating style for each opening, and we factor in Riverside’s heat load so you are buying the right Low-E coating, not just the cheapest unit.

02

Frame Prep & Removal

We protect the interior, pull the old window, and clean the opening down to sound framing. We repair any rot or damaged framing we find, square the opening, and install or repair flashing so it integrates with the wall’s weather barrier. A window is only as good as the opening it sits in, so we do not set a new unit into a bad frame and call it done.

03

Installation & Weatherproofing

We set the window plumb, level, and square, shim it, and fasten it per the manufacturer’s pattern. Then we insulate the perimeter gap with low-expansion foam, run backer rod, and seal inside and out with the right sealant. We re-finish the interior trim and exterior surround, test every sash for smooth operation, and schedule the building inspection.

Window installation crew setting a replacement window by BPP Construction in Riverside, CA

What We Install

BPP Construction installs every common residential window type. Single-hung and double-hung windows for traditional looks, horizontal sliders for wide openings, casements and awnings that crank open for ventilation, fixed picture windows for views, bay and bow windows that project from the wall, and garden windows for kitchens. We set egress windows sized to code for bedrooms, and tempered safety glass wherever the code requires it near doors, floors, and wet areas.

We work in vinyl, fiberglass, and aluminum frames. Vinyl is the workhorse for most Riverside homes: low maintenance, good insulation, and a fair price. Fiberglass costs more but resists the heat-driven expansion that warps lesser frames in our climate. Aluminum still has a place on certain modern and commercial-style elevations. We install reputable manufacturers, including Milgard, Andersen, Pella, and Simonton, and we match the brand and line to your budget and the look of the house rather than pushing one product on every job.

Glass matters as much as the frame in Riverside. We spec dual-pane insulated glass with Low-E coatings and argon fill to cut the heat that pours through single-pane and clear-glass windows in summer. ENERGY STAR rated units lower your cooling load and meet the efficiency standards California enforces under Title 24. We walk you through the glass options for each room based on sun exposure, so the windows on your west-facing wall are not the same spec as the shaded north side.

Ready to Replace Your Windows?

(909) 227-4193

Call Ben for a free on-site visit. We measure your openings, tell you whether you need replacement or new-construction windows, and give you a detailed quote. No pressure, no obligation.

Request a Free Quote
Related Services

Explore More from BPP

Exterior Painting

New windows look sharp against fresh paint, and the two jobs pair well. After we set your windows and finish the exterior surround, a full exterior repaint protects the siding and ties the new units into the rest of the house. We prep, prime, and paint to last in Riverside’s sun.

View Exterior Painting →

Stucco Repair

Cutting a window opening or swapping a new-construction window means working through the stucco, so stucco repair is part of many window jobs. We patch, re-texture, and color-match the surround so the repair disappears into the existing wall instead of standing out as a bad patch.

View Stucco Repair →

See completed window installs, exterior work, and remodels we have built throughout the Inland Empire in our project gallery.

Common Questions

Window Installation FAQs

Do I need a permit to replace windows in Riverside?
In most cases, yes. The City of Riverside and the surrounding jurisdictions require a building permit for window replacement when the work changes the size of the opening, alters the structure, or installs a new-construction window with a nailing flange. A straight retrofit replacement that drops a new unit into an existing sound frame without touching the rough opening sometimes falls under a simpler permit path, but bedroom egress windows, tempered-glass requirements near doors and floors, and any opening change always trigger a permit and inspection. California’s Title 24 energy code also applies, so the windows you install have to meet the U-factor and Solar Heat Gain Coefficient values for our climate zone, and the inspector checks for it. BPP Construction handles the permit application, the energy compliance paperwork, and the inspection for every window job we run, so you are not standing in line at the building department or guessing at code.
What window brands does BPP install?
BPP Construction installs reputable, widely supported manufacturers rather than tying every job to one brand. We regularly install Milgard, Andersen, Pella, and Simonton windows, and we will work with another line if you have a specific product in mind or your HOA requires a particular look. We choose the brand and the model line based on your budget, the style of your house, and the demands of the opening, because the right window for a west-facing living room in full Riverside sun is not the same as a shaded north-side bedroom. Every brand we install carries dual-pane insulated glass and Low-E coating options, and we register the manufacturer warranty in your name so the glass and frame coverage is yours. If you want to compare two specific lines side by side, Ben will walk you through the real differences in frame material, glass package, and price during the measurement visit.
How long does window replacement take?
A standard retrofit replacement window takes our crew roughly one to two hours per opening once we are on site and working, so a whole-house replacement of eight to twelve windows is commonly a one to two day install. New-construction windows take longer per opening because we open the wall, integrate flashing with the weather barrier, and re-finish both the interior trim and the exterior stucco or siding, which can add a day or more depending on how many openings are involved and how much surround work the job needs. The bigger variable is lead time on the windows themselves. Custom-sized and specialty units are built to order and can take three to six weeks to arrive from the manufacturer, while stock sizes move faster. We measure and order at the start so the windows are sitting at the shop ready to install when your install date comes, instead of leaving your openings sitting open. We give you a real timeline at the quote, not a guess.
What is the difference between replacement windows and new-construction windows?
The difference is how the window attaches to your house, and it decides the whole scope of the job. A replacement window, sometimes called a retrofit or insert window, is built to fit inside your existing window frame when that frame is still solid and square. We pull the old sashes and stops, set the new unit into the existing frame, and seal it, so the surrounding wall, stucco, and interior trim stay closed and untouched. That makes a replacement install faster, cleaner, and less expensive. A new-construction window has an integral nailing flange, a flat fin around the perimeter, that fastens directly to the wall’s framing. Installing one means opening the wall, removing siding or stucco, integrating flashing with the building’s weather barrier, fastening the flange, and then re-finishing the interior and exterior. New-construction windows are required when the existing frame is rotted or failing, when you are changing the size of the opening, or when you are building or adding on. During the measurement visit, Ben inspects your frames and tells you honestly which type your house needs before we quote it, so you are not paying for wall work you did not need or getting a retrofit shoved into a frame that should have been replaced.
What is an ENERGY STAR window and does it matter in Riverside’s climate?
An ENERGY STAR window is a unit certified to meet efficiency standards set for a specific climate zone, measured mainly by two numbers: the U-factor, which is how well the window resists heat transfer, and the Solar Heat Gain Coefficient, or SHGC, which is how much of the sun’s heat the glass lets through. In Riverside’s hot inland climate, the SHGC is the number that saves you money. Single-pane and clear dual-pane windows let summer sun pour heat into the house, and your air conditioner runs all afternoon fighting it. An ENERGY STAR window for our climate zone pairs dual-pane insulated glass with a Low-E coating and often argon gas fill to block a large share of that solar heat while still letting light in, which directly lowers your cooling bill and keeps west and south rooms livable in July and August. It matters here more than in mild coastal areas because our cooling season is long and brutal. California’s Title 24 energy code requires windows to hit minimum efficiency values anyway, so meeting the standard is required, and choosing a properly rated ENERGY STAR unit gets you real comfort and lower bills on top of code compliance. We spec the glass per room based on which direction it faces.
What does window installation cost in Riverside?
Window installation cost depends on how many openings you are doing, the frame material and glass package you choose, and whether the job is a straightforward retrofit replacement or a new-construction install that opens the wall. A retrofit replacement into a sound existing frame is the most affordable path because the wall stays closed and the labor per opening is lower, while new-construction windows cost more because of the wall, flashing, and re-finishing work. Frame material moves the price too: vinyl is the most budget-friendly, fiberglass costs more but holds up better in our heat, and specialty shapes, large picture windows, bay and bow units, and tempered or obscured glass all add to the per-unit number. Permit fees and any framing repair we find when we pull the old window also factor in. We do not quote window jobs sight-unseen, because a guess over the phone is worth nothing once we see your actual openings. Ben comes out, measures every opening, checks the frames, and gives you a detailed line-item quote with no obligation. Call (909) 227-4193 or reach us through our contact page to set up a free on-site visit.
Free On-Site Visit

New Windows Start with a Measurement

From a single fogged-up bedroom window to a whole-house replacement, BPP Construction measures, removes, installs, and seals every opening to California code and pulls the permit for the work. Call Ben today for a free on-site visit and a detailed quote.

Request a Free Quote Call (909) 227-4193

Where We Work

Based in Riverside, CA, serving homeowners across Riverside and San Bernardino counties.